Suppliers of steel products.

properties of 50 c steel

Leave a comment

51CrV4, 50CrV4, 1.8159, AISI 6150 - alloy steel

The steel, unlike other carbon and alloy grades, is characterized by high hardness, low vulnerability to tempering, resistance for variable and heavy loads, and the ability to operate at elevated temperatures up to 300 . Surface-hardened, retains excellent strength properties of the core while maintaining sufficient surface hardness. A500 Structural Tubing Steel A 500 Carbon Steel Spec SheetOutside diameter measurements for A500 carbon steel tube must be made at positions at least 2 (50.8mm) from either end of the tubing. For round structural tubing with nominal OD of 1.900 (48.26mm) and smaller, the outside diameter may not vary more than ±0.5%, rounded to the nearest 0.005 (0.13mm), of the specified size.

AISI 1050 Carbon Steel (UNS G10500)

Physical Properties Mechanical Properties Thermal Properties Other Designations Introduction. Carbon steels contain carbon as the main alloying element. They are designated by AISI four-digit numbers, and contain 0.4% of silicon and 1.2% of manganese. Molybdenum, chromium, nickel, copper, and aluminium are present in small quantities. ASTM A500 HSS - Steel HSS Atlas TubeASTM A500 HSS are cold-formed, welded and seamless carbon steel structural elements in buildings, bridges and other load-bearing applications. Atlas manufactures squares, rectangles and rounds. All shapes feature excellent compression and support characteristics, as well as superior torsional resistance, making HSS particularly well-suited to ASTM A572 Grade 50, 55, 60, 65 Steel Plates Specification A588/A588M Specification for High-Strength Low-Alloy Structural STeel, up to 50 ksi [245 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance; ASTM A572 Grade 50, 60 & 65 Data Sheet Properties. Chemical properties shall conform to the requirements prescribed in Table

C-50 Steel Chemical composition, Metal Properties

C-50 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86-80247006 E C50 steelTool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. C50 Round Bar C50 Flat Bar C50 Hollow Bar C50 Tube / Pipe C50 Sheet / Plate C50 Strip / Coil C50 Wire C50 Forging C50 Tube / Pipe TEL:+86-80247006 CSA G40.21 50W / 350W Structural, Carbon & HSLA Steel Chapel Steel Products Structural, Carbon & HSLA Steel Plate ASTM A36 ASTM A572 ASTM A588 ASTM A709 CSA G40.21 38W / 260W CSA G40.21 44W / 300W CSA G40.21 50W / 350W CSA G40.21 50A / 350A ASTM A656 ASTM A830 AISI 1045

Carbon steels [SubsTech]

Jun 01, 2012 · Dr. Dmitri Kopeliovich Carbon steels are iron-carbon alloys containing up to 2.06% of carbon, up to 1.65% of manganese, up to 0.5% of silicon and sulfur and phosphorus as impurities.. Carbon content in carbon steel determines its strength and ductility.. The higher carbon content, the higher steel strength and the lower its ductility. According to the steels classification there are Cold Rolled Steel C1144 Metal Supermarkets - Steel Grade Summary:Grade C1144 (also known as Stressproof® )is a medium carbon-free machining steel severely cold reduced to improve mechanical properties. Its inherent strength without heat treatment is comparable to heat treated steels of equal hardness. It is specially treated to relieve the stress created by the cold drawing, thereby minimizing the warpage after machining HSLA Grade 50 steel,HSLA Grade 50 Steel Mechanical ASTM A572 is an international material standard for billet steel for general structural usage. A-36 steel can be compared with this type of steel. HSLA Grade 50 Steel Chemical Composition :ASTM A572 defines the chemical composition of HSLA Grade 50 steels as under:Maximum percentage of Carbon (C

High Speed Steel D2 Steel D2 Technical Data

Relative Properties Physical Properties. Density:0.278 lb/in 3 (7695 kg/m 3) Specific Gravity:7.70 Modulus of Elasticity:30 x 10 6 psi (207GPa) Machinability:50-60% of a 1% carbon steel Heat Treating Instructions Hardening High Speed Steel Tool Steel O1 O1 Technical DataO1 Tool Steel. O1 Tool Steel is the original oil-hardening, non-shrinking tool steel that can be hardened to the Rockwell C 65 range from a low austenitizing temperature. O1 is a general-purpose tool steel that is typically used in applications where alloy steels cannot SAE AISI 4140 Steel Properties, Material Heat Treatment Heat treatment to 845 °C, slow cooling from 755 °C at a rate of 14 °C (25 °F)/hour to 665 °C, or rapid cooling to 675 °C for 5 hours isothermal annealing. Tempering. Tempering temperature of 4140 alloy steel can be from 204-649 °C (400-1200°F) after normalizing and oil quenching, and the corresponding Rockwell hardness can be obtained

Steel Standards - ASTM International

ASTM's steel standards are instrumental in classifying, evaluating, and specifying the material, chemical, mechanical, and metallurgical properties of the different types of steels, which are primarily used in the production of mechanical components, industrial parts, and construction elements, as well as other accessories related to them. Steel material properties - SteelConstructionfoThermomechanically rolled steel utilises a particular chemistry of the steel to permit a lower rolling finish temperature of around 700°C. Greater force is required to roll the steel at these lower temperatures, and the properties are retained unless reheated above 650°C. UNS S32750 (Alloy 2507) Stainless Steel ::MakeItFromThe graph bars on the material properties cards below compare S32750 stainless steel to:wrought duplex stainless steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half-full bar means it's 50% of the highest, and so on.

BS4360 50C|50C STEEL|50C STEEL PLATE__Steel Supplier

50C|50C STEEL|50C STEEL PLATE, with the specification of BS4360. Carbon steel plate, mainly used for the production of various types of steel rivet, steel bolt, steel weld and other structural components . Available size:Thickness:6mm--200mm. Width:900mm--3000mm. Length:3000mm to 18000mm